Duran Audio - IndustryAmp PB-400-DN

Duran Audio – IndustryAmp PB-400-DN

Product Information

The PB-400-DN Industry amplifier is an ultra-reliable, high-power, 4 channel (250W per channel) audio power amplifier designed for use in critical systems.

The PB-400-DN Industry amplifier is an ultra-reliable, high-power, 4 channel (250W per channel) audio power amplifier designed for use in critical systems. It is designed to drive 100 V line loudspeaker systems and is equipped with on-board DSP allowing gain, EQ, delay and other parameters to be controlled from a remote location using WinControl software, via DANTE™.

The amplifiers are fully monitored, with automatic fault detection and reporting. Inputs may be either balanced analogue audio or digital audio via DANTE™.

When used in conjunction with Duran Audio’s OpSTImizer® service the PB amplifiers can provide significant improvements in speech intelligibility within a tunnel.

Dynacord – IPX10:4

Dynacord's IPX10:4 is a 4 x 2500 W multi-channel installation DSP amplifier. Dynacord's IPX10:4 is a 4 x 2500 W multi-channel installation DSP amplifier.

4 x 2500 W multi-channel installation DSP amplifier with digitally controlled PFC supply
Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive
Dante and OCA integration via OMNEO with fallback options
Parallel, bridged and parallel-bridged drive modes with 70/100V and low impedance operation
High efficiency Eco Rail technology for lower operating costs

Amplifiers

Dante Ch: 8x2
48kHz-96kHz

See the product

Klangwert

KLANGWERT – i60D PoE+ amp

KLANGWERT PoE+ 2-channel amplifier with DSP.

The KLANGWERT PoE+ amplifier includes a Class D amplifier. Thanks to the use of a high efficiently power supply this amplifier is rated with 2x30 Watts RMS / 60 Watts peak (using a POE+ switch) into two channels. Inputs and outputs can be configured in different ways.

The internal powerful DSP board gives access to gain, delay, 10-Bd EQ with IIR filter and 24 internal presets.

The DSP is controlled by the PANC software in an IP network. All active AIMLINE and KLANGWERT digital systems can be controlled using just one software. Made in Germany

24V Power supply optionally available

Dimensions: 85 x 150 x 26mm (excl.connectors)

Amplifiers

See the product

Biamp

Voltera – D-2400-4

4-channel amplified loudspeaker controller, 2400 watts total power. Key Features

Integrated DSP provides essential capabilities for loudspeaker management
Up to 4800 W in single RU
Up to 8 channels in single RU
No central resource to limit system size
High peak voltage output capability (up to 237Vpk)
Power sharing provides up to 75% of total power through any single channel
Each model supports AVB, Dante, and AES67
Each channel can drive low impedance (2.7, 4, 8, and 16 ohm), 70V, or 100V
Onboard processing means system cost scales with power requirements
The ALAMOS loudspeaker profile library, with nearly 700 unique profiles covering over 200 Biamp models, saving valuable time during design and deployment
Group-controlled raised cosine EQ making it attractive for large systems
Accurate raised cosine EQ for the entire frequency band
Comprehensive limiter scheme avoids protective mutes and shutdowns
Processor can be sustained through PoE during power failures, avoiding reboots
Support for failover-to-analog operation
Wide dynamic range
5-year warranty
Compliant with the US Trade Agreement Act (TAA)
Biamp Workplace Ready

Amplifiers

AES67 Enabled

See the product

Duran Audio – IndustryAmp PB-400-DN

Product Information

Similar Products

Dynacord – IPX10:4

KLANGWERT – i60D PoE+ amp

Voltera – D-2400-4

Stay connected to Dante

Support

Company

Dante Networking Alliance