Cart
← Back to Product Catalog

Monacor – PA-900DT

Amplifiers

More details

Similar Products

leonis-SMA-OBIA2
  • Leonis Cinema

Leonis Cinema – SMA-OBIA

LIDSA32 (Immersive Digital Surround Amplifier-32 Channels) belongs to digital input CLASS-D power amplifier, digital interface access system, it adopts digital processing method in the whole process of signal processing and power amplification, in order to promote the speaker ,it uses low-pass filter to extract the analog audio signal in the CLASS. SMA-OBIA belongs to digital input CLASS-D power amplifier, digital interface access system, it adopts digital processing method in the whole process of signal processing and power amplification, in order to promote the speaker ,it uses low-pass filter to extract the analog audio signal in the CLASS. Each digital-analog conversion will produce a loss of sound, SMA-OBIA link reduces DAC conversion link. So our structure is more rational, more integrated. The sound of the output will be direct, dynamic amplitude larger, transient better. It effectively overcomes defects of the traditional analog amplifier (such as big volume, big distortion, low power efficiency, etc.). Its power utilization rate can be up to 95%. Features:
  • High integration,32 channels output
  • High power output, attain to cinema level
  • Digital input interface
  • 32 channels analog output
  • Over-current protection, overvoltage protection, over temperature protection
  • Adjust acoustic gain, status display, BTL-PBTL mode switch of per channel by network protocol
    Amplifiers
See the product
AMP203
  • AUDAC

AUDAC – AMP 203

The AMP203 is a revolutionary mini stereo amplifier, featuring network input through Dante™ or AES67 providing a complete media networking solution to distribute uncompressed audio via standard Ethernet networks with near-zero latency, while allowing all other data to be connected on the same network.

Various DSP functionalities are implemented in the AMP203. This allows all configurations to be made in AUDAC Touch™ 2 or via RS485 and Ethernet, making it a fully-fletched 2 x 30W amplifier. The output connector has been implemented using a 4-pin terminal block connector, featuring an output power of 30W per channel and 60W when bridged.

Using PoE (Power over Ethernet) this extremely power-efficient amplifier receives both power and signal through a single networking cable, this way flexibility is maximized while needed cabling is kept at a minimum.

The compact convection cooled enclosure eliminates any humm or buzz otherwise caused by a fan. Various optional mounting brackets are available like the MBS1xx series, which allow it to be mounted under a desk, in a closet, on the wall, on top of a dropped ceiling or to a 19" equipment rack. This proves that the AMP203 is the perfect solution for compact to medium-sized applications in corporate, hospitality or retail environments.

Decentralize your system

Thanks to the multifunctional use of the AMP203 in combination with the AUDAC Touch™ 2 app it is possible to create a decentralized multi-zone system. By simply connecting the AMP203 to the local network and connecting the loudspeakers, a new zone can be introduced to your system.

    Amplifiers
  • Dante Ch: 4 In
  • AES67 Enabled
See the product
ashly-nXe-1.54_600px|ashly-nXe-1.54_600px
  • Ashly Audio

Ashly – nXe1.54bd

The nXe1.54bd is a 2 channel multi-mode amplifier capable of driving 2 Ohm loads at full power. The maximum rated output power is 1,500W per channel at Low Z and 70V modes, and 1,250W in 100V mode. There is an automatic but defeatable sleep mode consuming <1W, and instant standby mode controlled by contact closure or software. A switch mode power supply auto-detects 120VAC or 240VAC mains, and a Neutrik® powerCON is used for the AC cord. Each channel has selectable output mode of Low Z, 70V, or 100V, an 80Hz high-pass filter, input limiter, and input gain settings of 26dB, 32dB, 38dB, or 1.4V. Each channel has remote DC level control. Input connectors is Neutrik® XLR/TRS combo jack and Euroblock, while output connectors is Neutrik® speakON. The unit has a front panel power switch and level controls that can be disabled. LEDs indicate Protect, Sleep, Disabled, Com, and Bridge mode status, as well as Temperature, Output Current, Output Signal, and Clipping/Mute status per channel. The unit has Ethernet control with a real-time clock for event scheduling. The unit has serial data remote control, aux preamp outputs, preset control, fault condition logic outputs, optional network audio and AES3 digital audio capability. The amplifier has temperature dependent variable speed forced-air cooling.
    Amplifiers
  • Dante Ch: 4 In
See the product