Cart
← Back to Product Catalog

MONISMS – MNS-AMP30XXA-2P

Amplifiers

More details

Similar Products

stewart-audio-mc850
  • Stewart Audio

Stewart Audio – MC850-MXZ-D

The MC850-MXZ-D has 6 channels @ 70/100V, and 2 channels @ 4/8 Ohm. The 1RU amplifier delivers 50W per channel with channel-to-channel power sharing. The MC850-MXZ-D has 6 channels @ 70/100V, and 2 channels @ 4/8 Ohm. The 1RU amplifier delivers 50W per channel with channel-to-channel power sharing. It has Ethernet and RS-232 control. The MC850-MXZ-D amplifier supports Dante™ audio and has AES67 support. The MC850 family embodies the future of smart amplification with networked audio inputs, Ethernet configuration, control and reporting and flexible power allocation between channels. Whether it’s low impedance, 70V/100V or a mix of the two, there is a model for you with 8 channels and a total of 400W. Setup and configuration can be done anywhere with network access allowing the installer to locate in the zone for real time feedback. The software is simple, intuitive and targeted in scope to make set up easy and allow for granular control. There are 8 independent Dante™ inputs. The MC850 family is AES67 compatible. We built the MC850 family with the network in mind and you’ll find it shows.       
  • 8 independent Dante™ inputs
  • Primary and Secondary Dante™ ports (redundant or switched)
  • Ethernet port for control and reporting
  • RS-232 control
  • Power sharing up to 100W per channel
  • Compact 1RU enclosure
  • Made in USA
    Amplifiers
See the product
210706-ma24lp2-persp1-7k_cut_low
  • Innosonix

Innosonix – MA24/LP²

The intention behind the Maxx series, which includes the LP², D² and HP² range, is to improve the total cost of ownership when it comes to a multi-channel solution. By offering the highest channel count per rack space in a single unit available on the market—complete with a comprehensive built-in DSP package—we believe we have achieved this intended goal.


Offering various audio-over-IP protocols, including Dante, combined with our industry-leading DSP capabilities (featuring 2048 taps of IIR/FIR filters, 32 points of parametric EQ, and precise delay and limiting per channel) provides integrators with the tools necessary to deliver a large loudspeaker solution with minimal sonic compromise.
The creative flexibility and improved cost performance of the Maxx series make these products extremely powerful tools.

 

MA24/LP² delivers 24×50W @4 Ω in only 1U of rack space.

    Amplifiers
See the product
CMX - Power amplifier with DSP & Dante
  • CMX

CMX – DSP-4350

The CMX DSP-4350 is a power amplifier with DSP and Dante.

  • 4 x 60W power amplifier
  • 100V, 70V, 4 Ohm & 8 Ohm output with selectors
  • Built-in DSP with EQ, gain control, crossover, delay, limiter, high-pass filter & low-cut filter
  • Dante network control with 4 In 4 Out matrix
  • Two Ethernet RJ-45 network connector for both Dante and DSP configure
  • Remote GPIO for failure outputs
  • 1U height 19” rack mount type power amplifier
  • Balanced line input by phoenix connector for four channels.
  • Each four inputs with separate gain control.
  • Separate four channel indicators for protection, clip, input and output.
  • Complete short circuit, overload, high temp, clip and DC protection.
  • Dante increases connectivity flexibility, and provides the freedom to use the amplifier power away from the source, wherever it is needed. It also enables the models to allow mixed inputs using either digital or onboard analog audio connections
    Amplifiers
See the product