Cart
← Back to Product Catalog

OMNI 256P

DSPs (Digital Signal Processors)

More Details

Similar Products

BLU-100_Front_full_width
  • BSS

BSS – BLU-100

The Soundweb London BLU-100 offers a fixed configuration of 12 inputs and 8 outputs, configurable signal processing and a high bandwidth, fault tolerant digital audio bus.

The BLU-100 has open architecture which is fully configurable through HiQnet™ London Architect. A rich palette of processing and logic objects and a “drag and drop” method of configuration provide a simple and familiar design environment.

This processor features a low latency, fault tolerant digital audio bus of 48 channels which uses standard Category 5e cabling giving a distance of 100m between compatible devices. Fiber media converters can be used to increase the distance between devices to over 40km.

The BLU-100 is compatible with the entire Soundweb London family and its 48 channel digital audio bus represents channels 1-48 of the larger 256 channel digital audio bus when integrated with the BLU-800, BLU-320, BLU-160, BLU-120 and BLU-BOB devices.

Analog Inputs provide software configurable gain in 6dB steps up to +48dB per channel and software selectable Phantom Power per channel.

Phantom Power, Signal Present and Clip information per channel is easily accessible, without the requirement for a PC, from clear front panel LED indication. A bi-directional locate function allows devices to be identified both from and within HiQnet London Architect.

12 Control Inputs and 6 Logic Outputs allow the BLU-100 to be integrated with GPIO compatible devices. The Soundweb London Interface Kit, comprehensive documentation which details how Soundweb London systems can be integrated with third party control systems, is included within the installation of HiQnet London Architect.

The BLU-100 and the other members of the Soundweb London family provide the building blocks of the perfectly tailored system solution.

    DSPs (Digital Signal Processors)
See the product
Core-NV-Right
  • Q-SYS

Q-SYS NV-32-H Core Capable

The Q-SYS NV-32-H (Core Capable) is a multipurpose, software-configurable video endpoint native to the Q-SYS Ecosystem, offering two distinct operating modes to choose between, based on the needs of the application. ‘Core Mode’ enables a consolidated Q-SYS AV processor, control engine, and local 3 x 2 HDMI video switcher to support video collaboration in small and medium-sized meeting rooms and classrooms. It features 32 x 32 network audio channel capacity, eight channels of software-based AEC, along with onboard audio I/O via HDMI, USB and 3.5 mm. ‘Peripheral Mode’ allows native HDMI and audio distribution without additional control processors, bridges or complicated programming. The NV-32-H (Core Capable) also lets you integrate Q-SYS video cameras and audio via USB into all major UC&C conferencing applications. Like all Q-SYS devices, the NV-32-H (Core Capable) offers native integration and control, simplifying setup, configuration and firmware management while eliminating the need for advanced programming knowledge.

    DSPs (Digital Signal Processors)
See the product
RX-8_ConnectorView-e1641507878211-1024x261-1
  • Zaxcom

Zaxcom – Rx-8

The RX-8 is an extremely small 8-channel receiver interface for your bag or cart. Accepting audio from up to 8 separate transmitters, the RX-8 contains a built-in MicPlexer with antenna distribution and front-end filter for eliminating interference from unwanted RF. It is the smallest 8-channel radio mic receiver system in the world!

An optional Dante interface with Power over Ethernet (PoE) facilitates remote location and control.

RX-8 can output 8 channels of analog or AES digital audio at 0 dB line-level on the DB25 connector. The RS422 connector pairs with a TRXCL4 or IFB300 to share the ZaxNet remote control commands. It has two SMA RF loop throughs for additional antenna distribution.

When the RX-8 is remoted on set you can send up to 16 channels of audio over Dante back to the sound cart, 8 originating from the RX-8 itself and 8 more via 4 AES pairs connected to the DB25.

When the RX-8 is remoted on set there is the option to send 4 channels of balanced analog audio from the sound cart to the set via Dante. The audio can be used for IFB, VOG, or monitoring. One of the audio channels can optionally be used to send timecode to the set. The timecode will then be output on the BNC connector on the RX-8 and can be used to jam slates or connect to a ZaxNet transmitter on set.

The RX-8 receives up to eight channels of audio from eight separate transmitters when loaded with 2 x MRX414 slot-in receiver modules.

The RX-8 has a front-end filter, so you can receive on any frequency in any block from 20 through 26 (512-698MHz) with impressive range. Here’s how that works – the filter allows signals within the 35 MHz tunable window into the receiver while blocking the interfering high-level signals outside this window. We let the good stuff in (your radio mic transmitters) and we keep the bad stuff out (walkie-talkies, the follow focus, vampires, etc.). Think of it like the bouncer outside a nightclub.

The RX-8’s built-in MicPlexer gives you an additional 3dB of RF amplification and antenna distribution for the two internal MRX slot-in receiver modules and additional receiver channels connected to the RF output connectors of the RX-8.

The MRX214 and MRX414 modules are hot-swappable and can be added or removed in any combination at any time, making the RX-8 highly flexible for when receiver requirements can change on a daily basis.

ENCRYPTION AND COMPATIBILITY

The RX-8 receives a 100% digital signal that is fully encrypted and is compatible with all Zaxcom modulations and transmitters.

INTUITIVE USER INTERFACE

Four OLED displays contain the menus for each receiver pair and tactile pushbuttons make receiver selection and toggling through menus a breeze. The built-in frequency scanner and Auto-Pick software eliminates the guesswork and can coordinate and choose the best frequencies with a push of a button.

POWER

The RX-8 is powered via a standard 12V Hirose connector.

With Dante, the RX-8 can be powered via the 12v input or remotely via power over ethernet (PoE). There’s also a 12v power output that supplies up to 1 amp for external receivers and transmitters when receiving PoE.

The 12V power Hirose input is a backup for the POE connection with seamless switching in the case of a PoE power issue.

RX-8 Rear

ADVANCED FEATURES

The RX-8’s built-in frequency scanner and Auto-Pick software can scan the RF spectrum and choose the best receiver frequencies. Using ZaxNet™, when paired with an IFB300 or TRXCL4, the RX-8 can re-freq transmitters to match it with just the touch of a button. This combo also lets you make quick and easy transmitter gain adjustments.

The groundbreaking RX-8 with Dante opens new frontiers of remote receiver control that has only been dreamt of in the past.

    DSPs (Digital Signal Processors)
See the product