Cart
← Back to Product Catalog

Panasonic – WP-DN360

Amplifiers

More details

Similar Products

stewart-audio-AV20-2-LZ-D
  • Stewart Audio

Stewart Audio – AV20-2-LZ-D

The AV20-2-LZ-D is a 2 channel PoE++ (60W port power or injector) Dante™ amplifier in a plenum-rated, compact, flange mount enclosure.   The AV20-2-LZ-D is a 2 channel PoE++ (60W port power or injector) Dante™ amplifier in a plenum-rated, compact, flange mount enclosure.
  • Two Dante™ input channels
  • Single category cable solution for both signal and power
  • Plenum rated package
  • AES67 support
The PoE++ Amplifier Series leverages the higher power 802.3bt PoE++ standard (60W port power) to power two amplifier models, the AV20-2-LZ-D (20W x 2 @ 4/8Ω) and the CVA40-1-CV-D (40W x 1 @ 70V/100V). These compact Dante™ amplifiers are designed to be single cable solutions for small/medium zones without the need for a local power outlet. This amplifier series leverages the ubiquitous nature of existing CAT 5e/6 cable in zones and also the inexpensive process of pulling new cable to zones. It creates an opportunity to reduce labor costs with a single, reliable, twisted pair cable that carries power and data to where you need it. Simply plug the PoE++ CAT 5e/6 cable into the amplifier, wire the speakers and route audio and repeat for the next zone. The plenum rating and compact size, allow this amplifier series to be placed in the air handling space, closets, the rack or any other convenient space. The confluence of readily available and inexpensive CAT 5e/6 cabling, Dante™ networked audio and quick installation, makes this amplifier series an essential problem solver.
    Amplifiers
See the product
Kevic_-_MA3232|Kevic_-_MA3232
  • Kevic

Kevic – MA3232

The Kevic MA3232 is a Dante Digital Power Amplifier.   The Kevic MA3232 is a Dante Digital Power Amplifier. Features:
  • In/out Channels:2XLR Balance with Link Ouputs
  • Rated Output Power :2 X 1600Watts 4 ohms
  • Power Band Width:10Hz-28KHz
  • Input Sensitivity:+4dBu(1.2Vrms)
  • THD at Rated Power: 0.05%
  • CrossTalk : Less Than 80dB
  • Signal to Noise Ratio: more than 104dB
  • Network audio Format : Dante BK2
  • Demansions,mm:482 x 88 x 432
  • Weight : 17Kg
    Amplifiers
See the product
nXp-3.04-front
  • Ashly Audio

Ashly – nXp3.04d

The nXp3.04d is a 4 channel multi-mode amplifier capable of driving 2 Ohm loads at full power. The maximum rated output power is 3,000W per channel at Low Z, 2,450W per channel in 70V mode, and 1,250W in 100V mode. There is an automatic but defeatable sleep mode consuming <1W, and instant standby mode controlled by contact closure or software. A switch mode power supply auto-detects 120VAC or 240VAC mains, and a Neutrik® powerCON is used for the AC cord. Each channel has selectable output mode of Low Z, 70V, or 100V, an 80Hz high-pass filter, input limiter, and input gain settings of 26dB, 32dB, 38dB, or 1.4V. Each channel has remote DC level control. Input connectors are Neutrik® XLR/TRS combo jack and Euroblock, while output connectors are Neutrik® speakON. The unit has a front panel power switch and level controls that can be disabled. LEDs indicate Protect, Sleep, Disabled, Com, and Bridge mode status, as well as Temperature, Output Current, Output Signal, and Clipping/Mute status per channel. The unit has Ethernet control with a real-time clock for event scheduling. The unit has serial data remote control, aux preamp outputs, preset control, fault condition logic outputs, optional network audio and AES3 digital audio capability. The unit has 32-bit DSP processing at 48kHz or 96kHz sampling rate. DSP functions include swept load impedance, gain, dynamics including autoleveler and ambient noise compensation, equalization including graphic, parametric, feedback suppressor, and FIR filters, a matrix mixer including automixing, crossover, delay, and a signal generator. The amplifier has temperature dependent variable speed forced-air cooling.
    Amplifiers
See the product