Product Information
1. Master amplifier unit. Only one master amplifier unit can be connected in one system.
2. One Emergency MIC.
Seikaku – AVS-906
Similar Products
- Ashly Audio
Ashly – nXp4004d
The nXp4004d is a 4 channel multi-mode amplifier capable of driving 2 Ohm loads at full power. The maximum rated output power is 400W per channel at Low Z, 70V, and 100V mode. There is an automatic but defeatable sleep mode consuming <1W, and instant standby mode controlled by contact closure or software. A switch mode power supply auto-detects 120VAC or 240VAC mains, and a Neutrik® powerCON is used for the AC cord. Each channel has selectable output mode of Low Z, 70V, or 100V, an 80Hz high-pass filter, input limiter, and input gain settings of 26dB, 32dB, 38dB, or 1.4V. Each channel has remote DC level control. Input connectors are Neutrik® XLR/TRS combo jack and Euroblock, while output connectors are Neutrik® speakON. The unit has a front panel power switch and level controls that can be disabled. LEDs indicate Protect, Sleep, Disabled, Com, and Bridge mode status, as well as Temperature, Output Current, Output Signal, and Clipping/Mute status per channel.
The unit has Ethernet control with a real-time clock for event scheduling. The unit has serial data remote control, aux preamp outputs, preset control, fault condition logic outputs, optional network audio and AES3 digital audio capability. The unit has 32-bit DSP processing at 48kHz or 96kHz sampling rate. DSP functions include swept load impedance, gain, dynamics including autoleveler and ambient noise compensation, equalization including graphic, parametric, feedback suppressor, and FIR filters, a matrix mixer including automixing, crossover, delay, and a signal generator. The amplifier has temperature dependent variable speed forced-air cooling.
- Amplifiers
- Dante Ch: 4x4
- 48kHz-96kHz
- AtlasIED
AtlasIED – IED1542NA-D
This product has reached "end-of-life" and is discontinued by the manufacturer
The 1542NA-D is a compact power amplifier module capable of driving small loudspeaker loads in a GLOBALCOM® system.The 1542NA-D provides two outputs, each with 4 watts of power into an 8Ω load. This makes the module ideal for powering small zones that are made up of only a few low-powered loudspeakers.The audio inputs to the module are through the Ethernet audio network and are configured from the GLOBALCOM® System Management Center. The 1542NA-D model allows the use of Dante™ audio networking protocols.The 1542NA-D is powered using standard PoE and draw a maximum power of 13 watts. If PoE equipment is not used, an input is provided for an external +48VDC power supply. A green power indicator LED is included to show that the unit is powered on. Each channel has a green LED indicator that illuminates when signal is present and a yellow LED to indicate clipping. Another yellow LED illuminates to indicate that the device is in thermal overload. When this condition occurs, the device will stop passing signal until the condition has cleared.The amplifier is provided in an enclosure that either mounts to a DIN rail or is screwed down on a panel or wall to allow for convenient installation in remote closets close to the loudspeaker zone.Features
- Available in single-channel or two-channel configurations
- Available with Dante™ audio network interface
- Control and configure using a web browser and GLOBALCOM® System Management Center
- Settings storage in non-volatile memory
- Full integration with theAtlasIED GLOBALCOM® vACS
- Utilizes IEEE 802.af Power over Ethernet (PoE)
- Removable connectors for easy installation
- Rugged DIN-rail or panel/wall mount enclosure
- Amplifiers
- Ashly Audio
Ashly – nXp754d
Introducing our newest addition to the NX Series of Multi-mode Amplifiers: Now available in 150 & 75 Watts per channel housed in a 1U chassis.
Multi-mode operation is standard on all nX amplifiers. Like it’s 2U models, choose from two or four channel configurations and set individual outputs to drive Low Impedance (2, 4, 8 Ohms), or 25V*, 70V, 100V Constant Voltage systems via rear-panel located DIP-switches. Add Ethernet (nXe) for monitoring and control, or add both Ethernet and Protea™ DSP (nXp). Expand onto a network with Dante™, CobraNet®, or AES3 digital inputs.
Adapt Worldwide with a universal switch-mode power supply with PFC (Power Factor Correction). Reduce power consumption using Ashly EMS™ (Energy Management System) by triggering a sleep mode that draws <1W, which meets the most aggressive Energy Star® benchmark†. Follow pre-scheduled preset settings including levels and sources using RTC Event Scheduler (Real-Time Clock on nXe & nXp models).
Remote Control ready via the Ashly Remote iPad® app, and/or hardwired Ashly remotes including analog (as well as serial) and Ethernet on nXe and nXp models. Monitor fault conditions and adapt via Ethernet and the onboard Fault Log included in nXe and nXp models.
- Amplifiers